We may earn a commission when you buy. The price stays the retailer's.

Advertising disclosure

How-to

How to pressure wash a wood deck

A deck is softwood until it proves otherwise. The washer that striped your neighbor's boards was usually too close, too narrow, or standing still. Chemical and a wide fan do most of a deck.

Updated November 18, 2026 · By Eric

Deck boards record every mistake. A groove from a 0-degree tip does not rinse out. The aim is a clean board that still has its surface, ready for whatever finish the wood actually needs.

Know the deck before you wet it

Solid wood, usually cedar, pine, or pressure-treated lumber, can be washed if you stay gentle. Composite, capped composite, and PVC are a different product. Their makers often specify a cleaner and forbid pressure washing, or they allow only a wide fan from a stated distance. If you have the brand, follow that page instead of this one.

Look for popped nails, soft spots, and peeling stain. Pressure will lift loose finish and drive water into a soft board. Screw down what you can, and plan to refinish if the old stain is already failing. Washing a deck and then leaving bare wood through a week of sun is how the boards go gray and blotchy. Have the finish, or the decision not to finish, before you start.

Read the PSI and GPM guide for the idea, then turn the aggression down. An electric washer is often the better deck tool because it is harder to overdo. The electric picks include machines whose working pressure is already in a saner range than a 3,400 PSI gas unit with a yellow tip an inch off the board.

A sequence that keeps the grain

  1. Sweep. Grit left on the deck becomes sandpaper once water is moving.
  2. Wet the plants and the wood. Dry wood plus a sudden high-pressure pass marks more easily.
  3. Apply a deck cleaner the label allows on wood. Bleach formulas change the color of wood and they hurt plants. If you use one, follow the bottle, keep it out of the pump unless the labels agree, and rinse the landscaping. The soap guide is the line between pump-safe concentrate and bleach.
  4. Let it dwell without drying. Agitate bad spots with a soft deck brush, along the grain.
  5. Rinse with a 25- or 40-degree tip. Keep the wand moving, tip several inches off the board, spraying with the grain. Overlap. If you see fuzz, back up and open the fan.
  6. Do railings and balusters with even less pressure. Spindles split, and the gaps hide your aim.
  7. Let the deck dry fully before you sand fuzzy grain lightly or apply finish. Moisture trapped under stain peels.

What leaves the zebra look

Standing still. Using a 15-degree or 0-degree tip because the green one felt slow. Sweeping across the grain so every pass cuts the earlywood. Holding a gas washer’s turbo nozzle on cedar. All of those write lines.

A surface cleaner makes this worse when it is set for concrete. The shroud hides the jets, and the path width does not match a 5-inch board. Prefer the wand, where you can see the fan.

Between boards, a careful pass knocks out debris. Jamming the tip into the gap soaks the joists and the ceiling below a second-story deck. If you can see daylight and the joists are already wet, stop and let it dry. Structure matters more than a perfect photo.

Gas washers are fine on a deck only if you have the discipline to use the wide tip and more distance. If that is not how you work, plug in an electric and accept a slower rinse. The wood will look better on Monday.

Questions people ask

What PSI should I use on a deck?

Start lower than you would on concrete, often well under 1,500 PSI at the wood, with a 25- or 40-degree tip and the wand moving. There is no single safe number, because cedar, pine, composite, and old finish all behave differently. If the surface fuzzes, you are already too aggressive.

Can I use a surface cleaner on a deck?

It is a common way to leave wand marks you cannot sand out evenly. The jets sit close to the board and you cannot see them. If you use one, test a hidden board at the lowest pressure that does anything, and stop at the first fuzzy grain. Most decks are better with a fan tip.

Should I wash a composite deck the same way?

No. Composite and PVC decking makers publish their own cleaners and often warn against high pressure. Follow that maker. A garden sprayer and a soft brush beat a 3,000 PSI wand on capped composite.

More guides